Mektek “Classic” module only. (Mektek “Plus” modules do not use Coinset Files) These generic Coinset Files should be suitable for most usages. Before using any other Coinset File check  the description carefully to ensure it is suitable for your requirements.  If in doubt contact Mektek for advice. NOTE: All the  generic coinsets below prompt for to a slug to be passed through the mechanism as part of the programming to give the operator the opportunity to adjust for rejection of the slugs. See the Operators Manual for details. If Slug drop is not required "Skip" the Slug drops during programming. If a Coinset File listed here is not available on your system go to the Software Download page and download the latest Coinset Files. MARS MS1000 family: MS1000 coinset files work on most of the MS1000 family including MS1600, MS1604, MS1610, MS1614, MS1900, MS1904, MS1910, ME1099, ME1100. Mech variants: If the mechanism is similar in shape to the above and the loom E1 fits the 20-way ribbon connector on the coin mechanism then use the MS1000 Coinset Files. MS1000 A add up to 6 new coins to segment 1 MS1000 B add up to 12 new coins ME111 family: ME111 coinset files work on most of the MS100 family including ME111, ME115, ME115TS, MS111B1, MS111, ME126, ME129, & MS130B1 (For the MS150 consult your Programmer supplier). Mech variants: If loom E2 or E8 fits the lower left-hand connector on the coin mechanism then use ME111 Coinset Files. ME111 A add up to 6 new coins to segment 1 ME111 B add up to 12 new coins NRI G13 Family: The G13 0000 and G13 6000 series require different Coinset Files. The G13 7xxxx is a front plate version. Notes: - For Totaliser variants the value of each coin is defined into  the mechanism during programming. Contact Mektek for specific coinsets. - G13 6000 series has selectable measuring parameters which are  defined for each coin being programmed in the Coinset File. For this reason mechanisms using the Generic Coinset Files below should  have their discrimination and acceptance thoroughly tested after  programming to ensure that performance levels are acceptable. G13-6000 A (Acceptor Only) Add up to 6 new coins 1-6, outputs/inhibits 1-6 respectively G13-6000 B (Acceptor Only) Add up to 12 new coins G13-0000 A (Acceptor Only) Add up to 6 new coins to channels 1-6 G18: Acceptor only – for Totaliser variants contact your Programmer supplier. G18-3000 A (Acceptor Only) Add up to 6 new coins (Output/inhibit 1-6) G18-3000 B (Acceptor Only) Add up to 12 new coins (output/inhibit 1-6 & 1-6) G10: These coinsets contain individual  coin values for each coin channel and change tube routing. For  other values contact Mektek.For G10-4000/5/6/9  contact Mektek. G10-4000Euro Adds coins 5c/10c/20c/50c/1euro/2euro to  channels 1-6 & 5c/10c/50c to coin tubes left/middle/right Coin Controls C220B: C220B A Add up to 4 new coins to channels 1-4 Output on pins 2,4,5,7 C220B B Add up to 8 new coins to channels 1-8 Output on pins 2,4,5,7 & 2,4,5,7 C335: C335 A add up to 5 new coins to channels 1-5 Output on pins 3,5,6,8,1 C335 B Add up to 8 new coins Output on pins 3,5,6,8,1. (Coins 6,7,& 8 twinned  with coins 1,2 & 3 respectively) C435 family: The routing of coins through the in-built sorter in the mechanism  can be defined in the memory of the mech or via an external header  routing plug. Generic Coinset files use the routing plug with  default route "A". The Piezo sensor is disabled in the Generic Coinset files for  all coins. C435 & C435A: C435 A Add up to 8 new coins (Binary Coding and Routing unchanged, Piezo disabled) C450 family: C450 A Add up to 6 new coins (Routing unchanged) C450 B Add up to 12 new coins (Routing unchanged) C120 family: The C120, C122 and C123 use the C120 Coinset Files. C120 C120 All New& Jaguar Type Add up to up to 6 new coins to channels 1-6 (Mapping unchanged) C120NewA   New type mechanism - add up to 12 new coins (Mapped 1-6 & 1-6) C120JaguarA Jaguar type mechanism - add up to 12 new coins (Mapped 1-6 & 1-6) C220,  C220A, Sentinel: Sentinel A add up to 4 new coins (Routing unchanged) Sentinel B add up to 8 new coins (Routing unchanged)